Home  |  Our Products  |  Our Projects  |  Request a Quote  |  About Us
IET Coating  |  Wastewater Services  |  Vac Truck Services  |  Confined Space Safety  |  Lift Station Rehab  |  Industrial Waterproofing
17660 East Street, North Fort Myers, Florida 33917 Phone: (239) 997-6645  FAX: (239) 997-7117
 

IET COATING'S SOLE APPLICATOR IN FLORIDA

 
     

IET Coating ... “Best Coating Method!”

 
    IET SYSTEMS Polymorphic Resin is stronger than any other concrete repair or coating product. IET penetrates into the open pores of concrete creating a structural attachment stronger than the concrete matrix itself. The strength of the concrete becomes the limiting factor in the adhesion. It can be used in place of cement and water as the binding agent for any aggregate mix used in concrete. This creates a super concrete that can be used for repairs to damaged concrete or the creation of monolithic structures. Adheres to steel and other metals creating a nearly indestructible coating. 

IET SYSTEMS has seven different combinations and unique blends of fillers and state-of-the-art application equipment to create an unsurpassed renovation and protection system for all wastewater processing facilities.

          IET Systems Technical Data Sheet  
The following “Deluxe Prep Method” allows Paints & Coatings, Inc. to provide a Ten-Year Unlimited Warranty for all
workmanship for all Wastewater Structures.
 
       IET Coating Procedures:
 
A.  The following shall be complete prior to IET Coating installation.
 
  • Sewer pipe shall be successfully tested.

  • Manhole invert shall be completed.

  • All leaks in the manholes will be injection grouted with Avanti Multi-Grout AV-202 or equivalent.   Hydraulic cement is not to be used to stop any water leaks.

  • Concrete grade rings will be installed with the manhole castings.

  • All pipes will be plugged or bypassed before any work is done on manhole.  No debris is to be flushed down the line.

  • Anyone entering a manhole must have all OSHA's "Confined Space Standard" equipment and permitting.

B.   Interior of manhole must be abrasive-blasted.  No silica sand is to be used.  (It has cancer-causing agents).
 
  • “New” manholes will be sandblasted to remove all form oils and patch mud, as well as, open pinholes and exposed aggregate.

  • “Rehab” manholes will be sandblasted until all loose patching, old coating and any contamination that penetrated the concrete has been removed.  The finished manhole should be gray with aggregate.  No contamination should be left.  The exposed invert/floor will be done as well.

C.  Remove abrasives and debris.  Pressure wash clean and force dry concrete.
D.  Surface preparation shall meet the requirements of IET Systems Data Sheet on Concrete Preparation DS-001 and interior surfaces of manhole shall be sound, porous, dry and free of dust, dirt, oil, grease and other contaminants prior to application of lining.
E.   Apply IET System Prime Coat by the use of the IET Systems Spray Unit and IET Systems Spincaster.  Prime coat shall be properly catalyzed and applied at the rate of 5 mil dry.  Prime coat application shall meet the requirements of IET Systems Prime Coat Data Sheet DS-101 and Equipment Data Sheet DS-601.
F.   After IET Systems Prime Coat has started to gel, fill all cracks, spalled areas or other damage with Quick-Set/ High Strength Grout.
G.   Apply IET Systems Intermediate Coat over gelled prime coat and grout repairs.  Apply intermediate coat with IET System Spray Unit and Spincaster.  Intermediate coat shall be a minimum of 50 mils.  Intermediate coat application shall meet the requirements of IET Systems Resin/Aggregate Data Sheets DS-301 and Equipment Data Sheet DS-601.
H.   Apply IET Systems Finish Coat over gelled intermediate coat.  Finish coat shall consist of IET Systems Polymorphic Resin and Bright White Isotholic Gelcoat.  Finish coat shall be a minimum of 5 mils.
I.   Inspect lining system for holidays and pinholes.  Take particular care to check lining over brick, block, concrete, and manhole joints.  Fill voids and holidays in accordance with the lining system manufacturer’s instructions.

 
 

            Ten-Year Unlimited Warranty

  Our deluxe prep system allows us to offer you a Ten-Year Unlimited Warranty for all workmanship.
Any type of applicator error will be fixed promptly within 72 hours of notification.

Carl A. Laquidara                                  Jeffrey A. Yingling
President
                                             Vice President